How Much Lawn Can Your Water Support? A Calculator for Wells, Cisterns and Rain Tanks
Start from your well, cistern or rain tank and find the square footage of lawn, shrubs or hedges you can keep alive through the hottest week of summer.
Your water supply sets the size of the lawn
Most irrigation advice assumes the yard comes first. You measure the lawn, work out the demand, then go find the water. That falls apart on a low-yield well, on a hauled-water cistern, or in a town that keeps tightening summer restrictions. The supply is already fixed, so the useful question runs the other way: how many square feet can this water carry through August?
Answer that before you seed or trench and you avoid the most expensive mistake in dry-climate landscaping, which is installing more turf than you can ever water. You can still have soft grass where the kids play or where you sit in the evening. It just gets sized to the supply, with lower-demand planting around it.
Run your numbers
Choose a source and replace the sample values with your own. Two sources? Run each one, add the gallons per day, multiply by seven and enter the total under Set budget.
Calculate how much yard your water can support
Pick your water source and enter your numbers. The result is sized for the hottest week of summer.
Enter your water source details to see the result.
Conservative estimate: it ignores rain falling on the yard and assumes a system efficiency of 72%.
The math behind the result
The calculator divides the gallons you can count on each day by the gallons each square foot needs at peak. Tall fescue in full sun, under a reference ET of 0.20 inches per day, uses about 0.19 inches. One inch of water over one square foot is 0.623 gallons, so the plant itself takes roughly 0.12 gallons a day. Sprinklers lose some water to wind, evaporation and uneven coverage, and at 72% efficiency you have to deliver about 0.16 gallons per square foot.
We size for the worst week on purpose. A lawn that survives the peak is comfortable the rest of the season, and the calculator gives no credit for rain falling on the yard, since a brief July storm on baked soil adds very little. Species differences are covered in Vegetation Types in SprinklerMap: How ET Values Drive Your Watering Schedule if you want to compare grasses in more depth.
Worked example: 1,300 gallons every 10 days in a hot climate
Here is a simulated case. A 1,300-gallon cistern gets refilled every 10 days, summer ET runs 0.24 inches a day, and the yard is in full sun. After leaving 10% in the bottom of the tank, that is 117 gallons a day.
| Planting | Gallons per sq ft per day | Area it can support |
|---|---|---|
| Cool-season lawn mix | 0.205 | 570 sq ft |
| Tall fescue | 0.196 | 590 sq ft |
| Low-input lawn mix | 0.164 | 710 sq ft |
| Bermudagrass | 0.143 | 810 sq ft |
| Shrubs and hedges on drip | 0.098 | 1,190 sq ft |
Choosing the right summer and sun settings
The three climate options stand for a reference ET of 0.16, 0.20 and 0.24 inches a day during the hottest stretch of the year. Many state climate offices, university extension programs and smart controllers publish daily ET from nearby weather stations, so look up July values across a couple of years instead of relying on one cool week. If you cannot find a local figure, pick the warmer option. Overestimating demand leaves you with spare water in August. Underestimating it means rationing a lawn you have already paid to install.
Sun exposure deserves the same care. A lawn shaded by the house through the afternoon can reasonably use part shade, while a strip that only sees shade early in the morning should stay on full sun. If your yard has both conditions, run the calculator once for each area and split your daily gallons between them.
Getting honest numbers from a well
A pump rating tells you what the pump can move. It says nothing about what the well can keep supplying. To find the sustainable figure, run the well on a dry summer day, time how long it takes to fill a container of known size, then repeat after 30 minutes and again after an hour. If the fill time keeps growing, the water level is dropping, and the last reading is the one to use.
A 3 GPM well pumping one hour a day yields 180 gallons. The calculator suggests taking 30% off for summer decline, leaving 126. That 30% is our cautious placeholder, so if you already measured the well in August, set it to zero. If your well is slow but steady, a storage tank lets it refill all day while a booster pump delivers the flow your sprinklers need during the watering window. The sizing method is in Irrigation Pump: How to Tell If You Actually Need One (and How to Size It).
Well permits, reporting and drought rules differ from state to state and sometimes county to county, so check with your state water agency or local health department before you drill or add irrigation to an existing well.
Rain tanks: your roof usually outruns your storage
Each inch of rain on a square foot of roof is 0.623 gallons, and installers commonly assume about 80% of it reaches the tank. A 1,000 sq ft roof in a 2.5-inch month therefore sends about 1,250 gallons your way. Whether you keep it depends on how the rain arrives. If that month brings two big storms, each one delivers around 625 gallons, and an 800-gallon tank catches both only if you have drawn it down between them.
That is why the calculator asks for the number of rain events as well as the monthly total. It starts with a full tank, tops it up at each event, and throws away anything above capacity. Use your driest month here rather than the annual average. Plenty of places look wet on paper and still go six weeks without meaningful rain in midsummer. State rules on collecting rainwater vary too, so confirm yours before you buy a large tank.
If the answer is smaller than the lawn you wanted
Change the grass first. In the example above, moving from a cool-season mix to bermudagrass adds 240 square feet on the same water, provided your climate suits it and you can live with winter dormancy.
Then look at sun. Part shade cuts demand by about 20% and full shade by about 40%, so the same fescue budget stretches from 590 to roughly 740 and 990 square feet. Where you put the lawn can matter as much as what you plant.
The layout that tends to work best is a compact lawn where you actually use it, surrounded by shrubs on drip. On 117 gallons a day you could keep 300 sq ft of tall fescue, which takes about 59 gallons, and spend the other 58 on roughly 590 sq ft of shrubs. That only works when each planting type has its own zone, which is what Hydrozones: split your garden to irrigate better walks through. For the smaller wins, such as mulch, a rain sensor and seasonal schedules, see How to cut lawn irrigation water use: the gallons, the bill, and which change saves the most.
Turn the number into a plan
Once you have a target area, draw it on a map of your property. SprinklerMap lets you outline that lawn, place the heads and see the daily gallons each zone needs before you buy any pipe.
Frequently asked questions
How many gallons a day does 1,000 sq ft of lawn need?
At a reference ET of 0.20 inches a day in full sun, 1,000 sq ft of tall fescue needs about 164 gallons a day with a typical sprinkler system. Bermudagrass needs about 119.
How much lawn can a 1,000-gallon tank water?
If it refills every seven days, it provides about 129 gallons a day after leaving 10% in the bottom. That supports around 780 sq ft of tall fescue at peak. Filled only once, it covers 1,000 sq ft for about five and a half days.
Can I combine a well and rainwater?
Yes. Work out the gallons per day from each source, add them, multiply by seven and enter the total under Set budget.
Why is the result lower than I expected?
It is sized for the hottest week and ignores rain on the yard, so the lawn holds up in the worst conditions. Spring and fall demand are much lower.
Recommended products
These product links are affiliate links: if you buy on Amazon through them it costs you nothing extra, but it helps us keep SprinklerMap alive as a project and create new useful content.
| Product | Description | Price (€) | Buy |
|---|---|---|---|
| Rainwater storage tank | Above-ground tank with a spigot and gutter connections. Pick the size from your calculation, and remember the bottom 10% is not usable. | ~€150-600 | Amazon |
| Submersible cistern pump | Delivers tank water at the pressure your sprinklers need. Check flow and head against your system before you order. | ~€100-350 | Amazon |
| Downspout rain diverter with filter | Fits your downspout, keeps leaves out and sends clean water to the tank, so less sediment settles on the bottom. | ~€20-60 | Amazon |
| Digital garden hose flow meter | Screws onto the spigot and logs the gallons used per cycle, an easy way to confirm you are staying inside your water budget. | ~€15-40 | Amazon |
Technical note: The calculator uses the same values as SprinklerMap: species ET referenced to 0.20 in/day, exposure factors of 1 / 0.8 / 0.6, and a system efficiency of 0.72 (distribution uniformity 0.80 × losses 0.90). Drip uses 20% less water, the cautious end of the 20-50% range reported by Pacific Northwest National Laboratory. Roof capture is 80%, the assumption cited by EPA WaterSense and the Texas Water Development Board. The 90% usable tank volume is our own assumption. The cistern example is simulated.