Published July 16, 2026 · Updated November 15, 2026 · 9 min read · by Giacomo Falaschi

How to fix a bare patch in the lawn (including the pre-germinated seed method)

Repair a bare spot in the lawn: find out why grass will not grow there, prepare the soil, sow dry or with pre-germinated seed, and keep the patch moist without flooding the rest of the sprinkler zone.

How to fix a bare patch in the lawn (including the pre-germinated seed method)
Foto: Will Clayton (BY 2.0)

Before you reseed, work out why the grass is missing

A bare patch in an otherwise thick lawn nearly always has a specific cause, and unless you remove it the patch comes back within weeks. The usual ones are traffic on the same line (the shortcut to the gate, the worn spot under a swing), compacted soil, standing water, dog urine, deep shade, or seed from an earlier sowing that dried out on the surface.

One cause sits in the irrigation system. If the patch browns every summer in the same place, halfway between two heads or in a corner, the water is probably not reaching it. Sprinklers need to throw all the way to the next head (head-to-head coverage, explained in Sprinkler Head Spacing: The One Decision That Decides Whether Your Lawn Goes Brown); when they are spaced too far apart, the strip in between gets too little water and thins out first. Before reseeding, set a few cups on and around the patch and run the zone as described in The catch-cup test: measure sprinkler uniformity and your real inches per hour. If the cups in the patch collect half of what the rest of the lawn gets, the fix is the sprinklers, not the seed.

Spots smaller than your fist, according to University of Wisconsin Extension, fill in on their own from the surrounding grass. And if the patch is on a route everyone walks, reseeding it every year is wasted effort: turn it into a path with stepping stones or mulch.

Dry seed or pre-germinated seed

The simplest method, and the one Wisconsin Extension recommends, is to mix a couple of handfuls of seed into a bucket of soil, spread it over the loosened spot and keep it moist until it germinates. It works well in spring and late summer, when the patch does not dry out in a few hours.

Pre-germinated seed is worth it when the patch is very exposed or you want to save time. You sprout the root under cover in a damp medium and only then move the seed to the patch. Golf courses use the same idea, with pre-germinated ryegrass for divot repair. Know its limit before you start: sprouted seed cannot go back. If it dries out even for a few hours, the young root dies, so only do it if you can water the patch several times a day for the next two weeks.

It suits fast species such as perennial ryegrass. Kentucky bluegrass takes weeks to germinate and is not a good candidate.

Dry seed or pre-germinated seed
Foto: seantoyer (BY 2.0)

Pre-germinating in sawdust, step by step

Use sawdust from untreated wood, never chipboard or painted timber. Wet it and wring it out until it is as damp as a squeezed sponge, then mix in the seed in a shallow tray. Cover with perforated film to slow evaporation and keep the tray indoors or somewhere sheltered, out of direct sun.

Check daily and mist if the surface dries. When a small white root shows on most of the seeds, they are ready. Do not wait for the roots to grow long and tangled, because they snap when you move them. Ryegrass needs only a few days; in a cool room it takes longer.

Sawdust is only a damp carrier here. It is very high in carbon and low in nitrogen, so as it breaks down, soil microbes use up the available nitrogen and the seedlings go yellow. That is why it must be mixed into real topsoil and stay the minor part. Damp paper towel or vermiculite work too.

Prepare the patch

While the seed sprouts, loosen the patch with a fork or trowel to 8-10 cm (3-4 in), breaking the surface crust. Remove stones, dry thatch and dead roots. On a compacted crust water runs off and roots cannot get in.

If you suspect standing water, pour a bucket into the loosened patch and time how long it takes to drain. A few minutes is fine; if it sits for a long time, the soil is compacted or heavy clay and needs deeper work. The same test tells you your soil type, and so how long a zone can run before water starts to run off: see How long to run sprinklers: minutes per cycle by soil and head type, with the math behind them. Finally level the base a few millimetres below the surrounding lawn.

Mix and cover

Mix fine seed-starting soil with the sawdust holding the sprouted seed, keeping the sawdust as the minor part (roughly one part to three or four of soil). Stir gently so the roots do not break, fill the patch to lawn level and cover with 3-5 mm (about 1/8 in) of plain soil. Press lightly with your palm, just enough for the seed to touch damp soil.

With dry seed the process is the same: mix the seed into the soil at the rate printed on the bag, scaled to the area of the patch.

Keeping the patch moist without flooding the zone

For the first two weeks the surface of the patch must stay moist. The schedule we use for new seed is three short cycles a day of about 1.5 mm (0.06 in) each, spread over the warm hours (for example 7 am, 12:30 pm and 5 pm), and no watering after 6 pm, when the surface would stay wet all night.

With a single patch you can do it in two ways. By hand, with a mister or a fine shower nozzle: a full jet digs out the mix and moves the seed. Or by adding short cycles to the sprinkler zone that covers the patch, which waters the whole zone. With fixed sprays (about 40 mm/h, 1.6 in/h) 1.5 mm takes just over 2 minutes; with MP Rotators (about 10 mm/h, 0.4 in/h) it takes 9. On a 540 sq ft zone each cycle applies about 20 gallons, so three a day for two weeks is roughly 830 gallons. How to work out the minutes for your nozzles, and how to taper the watering, is in Watering new grass seed: how many minutes per zone.

If you use the controller, bypass the rain sensor during germination and switch it back on afterwards, and remove the extra cycles once the grass has covered the patch. From then on water longer and less often so the roots go deep.

Which seed, and when

To avoid a patch of a different colour, use the same mix as your lawn if you know it. If not, pick a perennial ryegrass overseeding mix, which emerges in 7-10 days. Barenbrug states that its SOS mix germinates down to 4 °C (39 °F), useful in late autumn. In shade you need a mix with fine fescues, otherwise the patch goes bare again whatever method you use. The compositions and rates of common mixes are compared in Choosing lawn seed by sun, water and wear: species, labels and mixes.

The best window for cool-season grasses is late summer to early autumn, while the soil is still warm and the air is cooler; spring is the second choice. In the height of summer the patch dries in hours and needs constant attention; in midwinter the seed just sits there.

The first few weeks

Birds are the main threat at first: light netting or garden fleece protects the seed and holds moisture, and comes off as soon as the grass shows. Keep off the patch for three or four weeks so the soil does not compact again. If germination is thin in places, add a pinch of seed straight away.

Mow for the first time when the new grass is about a third taller than the height you cut the rest of the lawn, with a sharp blade so the seedlings are not pulled out. And deal with the original cause, whether traffic, standing water or a gap in sprinkler coverage, or the bare spot returns in the same place.

Frequently asked questions

Why pre-germinate grass seed instead of sowing it straight into the patch?

Germination in the open is where most seed is lost: birds, heavy rain and a surface that dries out. Sprouting the root indoors in a damp medium means the seed arrives in the patch already started. The catch is that sprouted seed cannot survive drying out, so from then on the patch has to stay moist all the time.

Which seed should I use to repair a bare patch?

Ideally the same mix as the rest of the lawn, so the patch does not show a different colour. Otherwise a perennial ryegrass overseeding mix, which emerges in 7-10 days. In shade you need a fine fescue shade mix.

How do I water one patch if I have an automatic sprinkler system?

Either by hand with a mister two or three times a day, or with extra short cycles on the whole zone. A 1.5 mm (0.06 in) cycle on a 540 sq ft zone uses about 20 gallons; three a day for two weeks comes to roughly 830 gallons.

Recommended products

These product links are affiliate links: if you buy on Amazon through them it costs you nothing extra, but it helps us keep SprinklerMap alive as a project and create new useful content.

In the catalogue From our brand catalogue

These products are catalogued in our brand database, with the same description and price range you find on the manufacturer page.

Blumen Blumen 1/5 products
Model Type Description Radius (m) Price (€) Buy
🌱 Prato Forte Rigenerante Seeds Mixture for thickening thin areas and restoring bare patches. Suited to localised work on small domestic lawns. — €12-22 Amazon
Barenbrug Barenbrug 1/6 products
Model Type Description Radius (m) Price (€) Buy
🌱 SOS Super Over Seeding Seeds Mixture for renovation and fast overseeding. Useful for closing thin patches after summer, after works, or where wear has damaged the turf. — €18-160 Amazon
Franchi Sementi Franchi Sementi 2/5 products
Model Type Description Radius (m) Price (€) Buy
🌱 Super Riparatore Seeds Solution for spot repairs of patches and small damage. Suited to quick work on domestic lawns. — €8-18 Amazon
🌱 Rigenerazione tappeti erbosi Seeds Mixture for overseeding and recovering thin lawns. Use it after light scarifying, with frequent watering during germination. — €10-22 Amazon

Other suggested products

Products not in the brand catalogue: generic material, tools and accessories where the right size matters more than the brand.

Amazon On Amazon Fast shipping and easy returns
Product Description Price (€) Buy
Perennial ryegrass overseeding / repair mix Fast-germinating repair blend for patches and thin spots on small domestic lawns, ideal to pre-germinate for closing gaps quickly. ~€10-25 Amazon
Fine seed-starting topsoil Light, sieved substrate to mix with the pre-germinated seed for good seed-to-soil contact and moisture retention in the hole. The proper base instead of sawdust alone. ~€8-18 Amazon
Garden netting / fleece for new seed Light cover to lay over the reseeded area to protect seed from birds and hold moisture in the first days, removed as soon as grass appears. ~€8-20 Amazon
Hand aerating fork Tool to loosen and decompact the soil in the hole before seeding, breaking crust and surface compaction on small areas. ~€15-35 Amazon

Technical note: Germination times are typical for each species (perennial ryegrass 7-10 days, tall fescue 10-14, Kentucky bluegrass up to three or four weeks) and run longer in cold soil. The mix ratios are a guide. Sprinkler run times depend on the precipitation rate of the nozzles in your zone: measure it with a catch-cup test before you program the controller.

Free tool: SprinklerMap is a free irrigation design software — draw your yard, let it place the heads with head-to-head spacing, and get a full parts list in minutes. Works in feet, GPM and PSI, or in metric: see the planner for Australia & NZ. Open the app →

Related articles