Published May 10, 2026 · Updated November 17, 2026 · 9 min read · by Giacomo Falaschi

How a sprinkler is built: anatomy and internal components

Discover every component inside a popup sprinkler: body, stem, nozzle, check valve and filter. Guide to disassembly, part replacement and seasonal maintenance.

How a sprinkler is built: anatomy and internal components
Foto: niranvv (BY 2.0)

The outer body and retractable stem

A popup sprinkler consists of a cylindrical housing (body) that stays fixed in the ground and an inner stem that rises during irrigation and retracts when pressure drops. The body is plastic, with a threaded inlet at the bottom: usually 1/2" on spray heads and 3/4" on rotors. It sits underground with only the cap exposed, so what cracks old bodies is mostly water freezing inside them in winter or knocks from mowers and spades, not UV.

How high the stem should rise is covered further down, with the physics of the stem. For model selection see Pop-up spray sprinklers: how to choose and the best models for sprays and Pop-up rotor sprinklers: complete guide to the best models for rotors.

The internal filter: the most neglected component

On spray heads a mesh filter (screen) sits just under the nozzle, inside the stem; on rotors, depending on the model, it sits under the nozzle or at the base of the stem. Its job is to catch sand, debris and lime scale before they reach the nozzle. A clogged filter cuts the flow and shortens the throw, causing dry patches in the lawn.

Clean the filter at least once a year, ideally at season end before winterisation. Pull up the stem, unscrew the nozzle and lift the screen out (a flat screwdriver helps). Rinse under running water and reinstall. For the full winter shutdown procedure see How to winterize a sprinkler system: drain or blow out, protect the backflow preventer, and restart in spring.

The internal filter: the most neglected component
Foto: JobyOne (BY 2.0)

The physics of how a stem rises with just 2 bar

The stem is the cylinder that slides vertically inside the body. When the zone valve opens, pressurised water enters from below and pushes against the underside of the stem. The force developed is F = P × A, where P is pressure (in Pascals) and A is the stem's cross-sectional area (in m²). At 2 bar (200,000 Pa) with a 20 mm-diameter stem (area 3.14 cm² ≈ 3.14 × 10⁻⁴ m²), the force works out to about 63 N, more than enough to overcome the stem's weight (a few grams) and the return spring.

Pop-up height depends on what surrounds the head: 4" (about 10 cm) is the standard for lawns, 6" (15 cm) for turf mown tall or ground covers, 12" (30 cm) for spraying over low beds. A head that is too short sprays into the grass and leaves a dry ring around itself.

The check valve (anti-drain)

The check valve is a small membrane at the base of the stem, called SAM (Seal-A-Matic) on Rain Bird and CV on Hunter. It opens under pressure (when the zone activates) and closes when pressure drops, preventing water from draining back into the pipe or leaking out when the zone is off.

Without one, water left in sloped pipes drains out through the lowest heads at the end of every cycle and leaves a puddle each time. It is not standard on every body: it comes as a separate version of the same head (Rain Bird 1804 and 1804 SAM, Hunter Pro-Spray and Pro-Spray CV), so choose it when buying the heads for the low points. Rain Bird rates its 1800 SAM bodies to hold back up to 14 ft (4.2 m) of elevation, Hunter its Pro-Spray CV up to 10 ft (3 m). The check valve is part of the stem assembly: if it fails, replace the stem. It is not a certified backflow preventer, which is a separate device on the supply.

The nozzle: where distribution happens

The nozzle is the interchangeable part screwed onto the top of the stem. It determines distribution sector (90°, 120°, 180°, 270°, 360°), radius and flow rate. Spray nozzles from the main manufacturers (Rain Bird, Hunter, Toro) share the same thread, so they physically fit most spray bodies, although matching nozzle and body brands still gives the most accurate arc.

Two adjustments are available: rotating the small side deflector changes the sector angle; turning the radius adjustment screw reduces throw by up to 25% without changing nozzles. This adjustment is critical to avoid watering walls or paths. For nozzle selection guidance see How to choose sprinkler nozzles for uniform lawns.

The return spring and the cap

At the base of the stem sits a stainless steel coil spring that pulls the stem back into its retracted position when pressure drops. If the stem stays partially extended after the zone closes, the spring is worn and the whole stem assembly should be replaced.

The cap at the top of the body holds the wiper seal that keeps grit out as the stem rises and falls. On spray heads the nozzle sits directly on the stem; on gear-drive rotors the nozzle sits in a turret that the drive turns slowly from side to side.

Rotor drive: a turbine and a gear train

Rotors (Hunter PGP, Rain Bird 5000, Toro T5) have a drive that spray heads lack. Incoming water spins a small turbine at high speed; a gear train slows that down and turns the head slowly across its arc. Depending on the model, the gears are lubricated by the water itself or enclosed in a sealed gearbox.

If a rotor turns in jerky steps, or stops while it still has pressure, the drive is almost always the cause: sand in the turbine or a worn gear. Gears are not repaired: you replace the internal assembly, which unscrews from the body without digging it up, or the whole rotor if the body is damaged.

When to replace parts vs. replace everything

Blocked or broken nozzle: replace the nozzle only (€1–3). Stem that will not retract: replace stem and spring (€3–8). Cracked body or damaged thread: replace the whole body (€5–15). Water spurting around the stem while the zone runs: rinse the cap, and if it still leaks replace the cap or the stem assembly, since the wiper seal is part of the cap.

When failures start repeating on several heads of the same zone, consider replacing the whole zone: the bodies went in together and age together, and changing them one at a time means digging again every few months. Keep a few spare nozzles, filter screens and one spare stem assembly per head type: they cover the common failures.

Key takeaways

A pop-up sprinkler is built around a few parts: body (fixed in the ground), stem (rises under pressure), filter (prevents nozzle clogs), return spring, nozzle (controls arc and radius) and, on the versions that have one, a check valve (stops back-draining). The most frequent maintenance tasks are cleaning the filter (annually) and replacing the nozzle (when arc coverage changes or output drops). A few nozzles from the same series, a couple of filter screens and one spare stem per head type cover the common failures.

Frequently asked questions

Why does my sprinkler leak at ground level when the zone is off?

Usually the water left in the pipes is draining downhill and coming out of the lowest head. A body with a check valve (SAM on Rain Bird, CV on Hunter) stops it; if the head already has one, the check valve has worn and the stem needs replacement. If every head on the zone keeps leaking, the zone valve is not closing fully. Water spurting around the stem while the zone is running is a different fault: the wiper seal in the cap is worn or has sand in it.

Can I use Rain Bird nozzles on a Hunter body (or vice versa)?

The standard 1/2" thread is nominally the same, but the nozzle-to-stem taper and deflector geometry differ between brands. Mixing brands is possible for emergency repairs but may reduce arc accuracy. For best results, use nozzles from the same manufacturer as the body.

How do I know if a sprinkler head needs replacing vs just cleaning?

Clean the filter and nozzle first. If throw and pattern come back, you are done. If the stem no longer retracts, if the lowest head keeps draining after the zone shuts off, or if a rotor has stopped turning, replace the internal assembly, which unscrews from the body. If the body is cracked or the thread is stripped, replace the whole head.

Recommended products

These product links are affiliate links: if you buy on Amazon or AliExpress through them it costs you nothing extra, but it helps us keep SprinklerMap alive as a project and create new useful content.

In the catalogue From our brand catalogue

These products are catalogued in our brand database, with the same description and price range you find on the manufacturer page.

Hunter Industries Hunter Industries 1/15 products
Model Type Description Radius (m) Price (€) Buy
💧 Pro-Spray PROS-04 Pop-up Fixed 10 cm pop-up body with ½" inlet, compatible with Pro fixed nozzles and with MP Rotator nozzles. The nozzle is bought separately and chosen for the radius required. 2.5–10 m €3-9 Amazon
Rain Bird Rain Bird 1/10 products
Model Type Description Radius (m) Price (€) Buy
💧 1804 Pop-up Residential 10 cm pop-up body, the most common choice for lawns. VAN or MP nozzle bought separately; broad compatibility with all standard nozzles. 1.5–5 m €3-9 Amazon

Other suggested products

Products not in the brand catalogue: generic material, tools and accessories where the right size matters more than the brand.

Amazon On Amazon Fast shipping and easy returns
Product Description Price (€) Buy
Rain Bird nozzle replacement kit (30 pcs) Assorted spray nozzle set for Rain Bird 1800 series: 90°, 120°, 180°, 360° sectors with radii from 1.5 to 4.5 m. Standard thread for all Rain Bird bodies. ~€18-30 Amazon
Sprinkler nozzle removal tool Dedicated tool for removing and reinstalling nozzles without damaging the deflector. Compatible with Rain Bird, Hunter and Toro. ~€8-15 Amazon
EPDM O-ring and seal kit for irrigation Assorted EPDM O-ring set for sprinklers and fittings. Resistant to chlorine and weather. Includes 50 sizes. ~€8-18 Amazon
AliExpress On AliExpress Cheaper alternatives, slower shipping
Product Description Price (€) Buy
Interchangeable popup sprinkler nozzle kit Assorted spray nozzles for standard 1/2" popup bodies. 90°, 120°, 180°, 360° arcs with adjustable radii. Compatible with Rain Bird, Hunter and generic bodies. ~€10-20 AliExpress
Assorted O-ring kit for irrigation fittings 200+ NBR rubber O-rings for sprinklers, fittings and valves. UV and water resistant. Includes the most common sizes for irrigation system maintenance and repair. ~€5-12 AliExpress

Technical note: The specs, coverage radii and price ranges quoted in this article are based on manufacturer datasheets and public catalogues. None of the models mentioned was tested directly: the comparison is on the specifications declared by the manufacturers. Figures can vary between models and after a product line is updated. Before buying, always check the current datasheet of the specific product you're considering, since stated performance changes with the actual operating pressure of your system.

Free tool: SprinklerMap is a free irrigation design software — draw your yard, let it place the heads with head-to-head spacing, and get a full parts list in minutes. Works in feet, GPM and PSI, or in metric: see the planner for Australia & NZ. Open the app →

Related articles