Why Evapotranspiration Is the Foundation of Modern Irrigation: the FAO-56 Paper Explained
What FAO Paper 56 (Allen et al., 1998) says, why Penman-Monteith became the standard for a garden's water needs, and what it means in practice.
The number almost nobody checks before watering
Anyone who deals with irrigation, professional or homeowner, tends to fall back on rules of thumb: 'twice a week', 'early morning', 'a finger in the soil'. Those are useful, but none of them says how much water the garden lost in the last 24 hours. That amount is called evapotranspiration, and it has a reference document that has been the standard used by agronomists, smart controller manufacturers and weather services worldwide since 1998: the FAO Irrigation and Drainage Paper No. 56.
It's among FAO's most cited publications. Outside agronomy circles, though, almost nobody has read it, and plenty of online content name-drops 'Penman-Monteith FAO-56' without explaining what the document says or why it became the standard. Here we explain it for people who look after a garden, without assuming the technical background.
The paper at a glance
| Section | Content |
|---|---|
| 🎓 Paper | Allen, R.G., Pereira, L.S., Raes, D., Smith, M. (1998). Crop Evapotranspiration: Guidelines for Computing Crop Water Requirements. FAO Irrigation and Drainage Paper No. 56, FAO, Rome |
| ❓ Question | How can water loss from a crop (or a lawn) to evaporation and transpiration be calculated in a standard, reproducible way that's comparable worldwide? |
| 🔬 What they did | Adopted a single equation, the FAO Penman-Monteith, as the worldwide reference: it was chosen in 1990 by an FAO expert consultation on the basis of lysimeter comparisons (an ASCE study of 20 methods at 11 locations and a European study), and its calculation was standardised from the weather inputs to the crop coefficients |
| 📈 What they found | Against lysimeters, Penman-Monteith gave accurate, consistent estimates in arid and humid climates alike; the modified Penman of the earlier FAO-24 often overestimated, by up to 20% under low evaporative conditions, and simpler methods need local calibration |
| 🌱 What it means for your garden | How much water your lawn loses each day depends on temperature, humidity, wind and solar radiation combined, which no fixed calendar rule can follow. In the same spot, a windy July day can lose twice as much water as a cloudy May day |
| 🗺️ How it connects to SprinklerMap | FAO-56 says how much water the plant needs, not how to distribute it. SprinklerMap estimates the need from fixed values by vegetation and exposure and handles the hydraulic side: a perfect ET calculation achieves nothing on a system that soaks half a zone twice as much as the other |
| 📚 References | See the References section at the end of the article |
The question: why a universal method was needed
Before 1998, anyone estimating a crop's or a lawn's water needs had dozens of different methods to choose from (Blaney-Criddle, Hargreaves, Thornthwaite, Class A pan evaporation and others: a 1990 ASCE study compared 20 of them), many calibrated to a specific climate and often disagreeing with each other on the very same site. An agronomist in California and one in southern Italy could apply different formulas and get non-comparable results, even starting from the same raw weather data.
FAO had already tried to solve this in 1977 with the earlier Paper No. 24, but subsequent tests against lysimeter networks (tanks that directly measure water lost from soil, the most reliable instrument for validating any formula) showed that its modified Penman, considered the most accurate of the four methods it proposed, often overestimated ET0, by up to 20% under low evaporative conditions, and that the others gave results that varied with the climate. In May 1990 FAO convened a panel of experts with a specific goal: a single, physically grounded equation, valid everywhere in the world, that required only easily measurable weather data.
What they did: from the original Penman to the FAO-56 version
The starting point is the Penman-Monteith equation, which combines the energy balance (how much solar energy reaches the surface) and aerodynamic transport (how effectively wind and humidity carry water vapour away) into a single physical formula. Unlike empirical methods, it isn't calibrated to a specific climate: it derives from thermodynamics and atmospheric physics, so in theory it works the same way everywhere.
FAO-56's specific contribution was standardising the parameters of a 'reference crop', a hypothetical grass surface 12 cm tall with a fixed surface resistance (70 s/m) and albedo (0.23), so the result (called ET0, reference evapotranspiration) is the same regardless of who calculates it, as long as the same weather inputs are used: maximum and minimum temperature, relative humidity, wind speed at 2 metres, and solar radiation (or sunshine hours, from which it's estimated).
The choice rested on two lysimeter comparisons already published: the study by the ASCE (American Society of Civil Engineers), which had tested 20 methods against screened data from 11 locations with different climates, and a similar European study. In both, Penman-Monteith had proved accurate and consistent in arid and humid climates alike.
What they found: why Penman-Monteith won
The central finding is that Penman-Monteith gave the most accurate and consistent estimates against lysimeters, in arid and humid climates alike. The other methods work in some climates and less well in others: radiation methods do well in humid climates but tend to underestimate in arid ones, the evaporation pan gives erratic results, and temperature-only methods need local calibration. Among those, FAO-56 names Hargreaves as the most reliable, to be used when humidity, wind and radiation data are missing.
FAO-56 then sets out the two-step calculation that ET-based smart controllers also use: first calculate ET0 (the standardised reference lawn's water need) from weather data, then multiply by a crop coefficient Kc specific to the actual plant. For turf, the FAO-56 tables give a Kc of 0.90-0.95 for cool-season grasses (bluegrass, ryegrass, fescue) and 0.80-0.85 for warm-season ones (Bermuda, St. Augustine), which can be lowered by 0.10 where water is carefully managed and fast growth is not needed. ETc (the real water need) = Kc × ET0. It's the same principle already covered, from the smart-controller side, in Smart sprinkler automations: rain delay, soil moisture and freeze skip that actually work.
A concrete figure to picture this: on a summer day in the 90s°F with moderate wind and clear skies, ET0 typically runs 6-8 mm; on a cloudy late-spring day it can drop to 2-3 mm. With the same Kc, the lawn's real water need on those two days differs by a factor of three, which a fixed 'twice a week' rule ignores.
What it means for your garden
It follows that a fixed-schedule timer is almost always wrong: it delivers the same amount of water regardless of whether yesterday was 95°F, dry and windy or 72°F and overcast. ET-based (weather-based) controllers solve this by pulling local or nearby-station weather data and recalculating ET0 daily to adjust cycle length. According to the US EPA's WaterSense programme, replacing a standard clock timer with a weather-based controller saves an average home about 7,600 gallons a year, close to 29 m³.
For anyone without (or unwilling to buy) a smart controller, the principle is still useful manually: on hot, windy, dry days the lawn loses more water and needs longer or more frequent watering; on cool, humid days the need drops sharply, and sticking to the same schedule just wastes water and encourages root rot.
How this connects to SprinklerMap: what it confirms, and what the tool does not do
SprinklerMap does not calculate daily ET0 with Penman-Monteith and does not download live weather data. It uses fixed seasonal water-need values by vegetation type and sun exposure to estimate the water target, litres and run times on the drawing, and combines that estimate with the hydraulic side: sprinkler placement, coverage, flow, available pressure per zone and the materials list.
FAO-56 stops at how much water the plant needs. Distributing it is a separate problem, and an accurate ET calculation achieves little if the water doesn't reach the ground evenly: a poorly placed sprinkler that soaks one spot twice as much as another defeats any precision in the theoretical water-need calculation. An ET calculation, with any method, only makes sense on a well-designed system, and that design work is what SprinklerMap does. For the soil-based run-time calculation side, the practical guide is How long to run sprinklers: minutes per cycle by soil and head type, with the math behind them.
The short version
Thanks to FAO-56, 'how much to water' can be calculated instead of guessed. Penman-Monteith beat earlier methods because it rests on physics instead of being calibrated to a single climate, and the smart controllers that set run times from evapotranspiration apply this 1998 paper. Understanding the principle makes it easier to interpret whatever number your smart controller's app shows you.
References
Allen, R.G., Pereira, L.S., Raes, D., Smith, M. (1998). Crop Evapotranspiration: Guidelines for Computing Crop Water Requirements. FAO Irrigation and Drainage Paper No. 56. Food and Agriculture Organization of the United Nations, Rome. Open access: fao.org/4/x0490e/x0490e00.htm
Pereira, L.S. et al. (2015). Crop evapotranspiration estimation with FAO56: Past and future. Agricultural Water Management, 147, 4-20. doi.org/10.1016/j.agwat.2014.07.031
Frequently asked questions
Are ET0 and ETc the same thing?
No, and mixing them up is a frequent mistake when reading an evapotranspiration figure. ET0 is reference evapotranspiration: that of a standardised lawn, well watered and unstressed, which for the same weather is identical anywhere in the world. It exists precisely as a common unit of measure, and it is how FAO-56 makes different climates comparable. ETc is the actual need of the plant you have in the garden, and you get it by multiplying ET0 by the crop coefficient Kc, which depends on the species and its growth stage. In practice: controllers and weather services give you ET0, but the water to give your lawn or hedge is ETc. Using ET0 as if it were the requirement means irrigating on a number that does not describe your plants.
Do I need a weather station in my garden to use these calculations?
No, and in most cases it is not worth it. Smart controllers on the market pull data from nearby public weather stations or from services like Open-Meteo, and for calculating evapotranspiration that is almost always enough: the variables that matter, meaning temperature, humidity, wind and radiation, change little within a few kilometres. A personal station such as an Ecowitt improves precision and makes sense if your garden has a marked microclimate: very windy, heavily shaded, at the bottom of a valley or unusually exposed. It stays a refinement rather than a prerequisite: the FAO-56 method was designed to work with standard weather data available anywhere, not with dedicated instruments installed on site.
Is the FAO-56 method still considered valid in 2026?
Yes. It remains the internationally recommended reference method, and the original authors re-examined it in 2015, seventeen years on, in the light of the research published in the meantime. The conclusion of that review, which we cover in the next article in this series, is that the 1998 framework held: the Penman-Monteith equation for reference ET held up in comparisons across very different climates. Real refinements did arrive, mostly on the dual crop coefficient and on the distinction between transferable and non-transferable Kc values, and they make the method more precise without replacing it. For a garden, a calculation based on FAO-56 is still current.
Why not just use temperature, which is easier to measure?
Because temperature on its own ignores two variables that weigh as much as it does: wind and air humidity. At the same temperature, a windy dry day can make the lawn lose twice the water of a calm humid one, because moving air carries the vapour away from the leaf surface and the process starts again. This is exactly the limitation the paper documents for simplified methods: measured against lysimeters, meaning against direct measurements of the water lost, temperature-only methods need local calibration, radiation methods tend to underestimate in arid climates and the evaporation pan gives erratic results, while Penman-Monteith gave accurate, consistent estimates in both arid and humid climates.
Technical note: This article explains, in plain language, the findings of a published scientific study, necessarily simplifying the original methodology to make it readable. For the full statistical analysis, the limitations the authors themselves note, and the experimental details, always refer to the original paper linked in the references at the end of the article: a study's results shouldn't be generalised automatically to your specific case.