Published May 15, 2026 · Updated November 17, 2026 · 8 min read · by Giacomo Falaschi

Rain sensor for irrigation: legal requirement and how it works

How rain sensors work on an automatic irrigation system, where to mount them, how to wire them to the controller, and where they are required by law.

Rain sensor for irrigation: legal requirement and how it works
Foto: Roger Soh (BY-SA 2.0)

What a rain sensor is and why irrigation systems need one

A rain sensor is a small device that interrupts an automatic irrigation system when it detects rainfall above a configurable threshold. Without one, a fixed-schedule controller runs its programme regardless of the weather: it waters through a downpour and soaks soil that is already wet.

Few places require a rain sensor by law. Florida is one of them: section 373.62 of the Florida Statutes requires automatic sprinkler systems to have a device that shuts irrigation off after enough rain. Elsewhere any obligation comes from local water authorities and drought restrictions, so check the rules where you live before commissioning a system. Either way, the sensor pays for itself quickly: one skipped cycle on a 200 m² lawn at summer peak is about 1.4 m³ of water (5 mm of demand divided by 0.72 efficiency), so around ten skipped cycles cover the cost of a €20–40 sensor.

How a rain sensor works

The most common type uses hygroscopic (moisture-absorbing) discs, thin wafers that expand when wet and contract as they dry. When rain falls, the discs swell, pushing a contact open and breaking the controller signal. Irrigation stops immediately, regardless of the scheduled programme.

Once the discs dry, typically within 4–48 hours depending on temperature, wind and the sensor's vent setting, the contact closes again and scheduled irrigation resumes on its own.

A second type uses electronic tipping-bucket detection: a miniature funnel counts rainfall in millimetre increments so the controller receives the amount of rain rather than a simple on/off signal. They are less common in home gardens than disc sensors. Many smart controllers (Rachio, Hydrawise) take rainfall from online weather data and still accept a wired sensor on their sensor input.

How a rain sensor works
Foto: Arlington National Cemetery (PDM 1.0)

Where to mount the sensor

The sensor must be exposed to direct, unobstructed rainfall. Good mounting positions: on a fence post at 1.5–2.5 m height, on the fascia board at the roof edge (outside the overhang), or on a garden wall at 1.5–2.5 m. Avoid positions under trees, roof overhangs, or structures that shield the sensor from rain.

Exposure matters too. On a very sunny south-facing wall the discs dry before the soil and the sensor re-enables irrigation too early; in constant shade on a north wall the opposite happens and the system stays off longer than needed. The right spot gets the same sun and wind as the garden. If you cannot choose, use the vent ring: partly covering the holes makes the discs dry more slowly. Keep the sensor out of the sprinkler spray as well.

How to wire a rain sensor to the controller

All standard wired rain sensors use a two-wire connection. On most controllers there is a dedicated SENS terminal pair, labelled SEN or SENSOR. Connect the two sensor wires to these terminals, then remove the jumper that was bridging them. The jumper is a factory bypass that disables the sensor input, and if you leave it in, the sensor has no effect.

On controllers without a SENS terminal, connect the sensor in series on the common (COM) wire. When rain triggers the sensor, it opens the COM circuit, preventing any zone from opening even if the programme fires. This works on 24 V AC controllers; on battery controllers with latching solenoids it does not, because the sensor would also block the pulse that closes the valve.

Wireless sensors communicate via a radio receiver that plugs into the SENS terminals. No cable run is needed, which helps when the sensor is mounted far from the controller.

Adjusting the rainfall threshold

Most adjustable rain sensors have a dial setting from 3 to 25 mm. Below the set amount, the sensor allows irrigation as normal. At or above it, irrigation is interrupted until the discs dry.

For most garden soils, start with a threshold of 5–6 mm. Five millimetres of rain on a 200 m² garden delivers approximately 1,000 litres, enough to satisfy a lawn's daily summer water demand without supplemental irrigation. Then adjust by watching the garden: if the sensor stops irrigation after a light shower and the lawn suffers, raise the threshold; if the soil is still damp when irrigation resumes, lower it or partly close the vent ring.

Wired vs wireless rain sensors compared

Wired sensors are the simplest, most reliable, and cheapest option (€20–40). They need a two-wire cable from the mounting position to the controller, typically 5–30 m. Hunter Mini-Clik and Rain Bird RSD are the two most widely specified wired models.

Wireless sensors cost more and transmit to a receiver wired into the SENS terminals, eliminating the cable run. Hunter Wireless Rain-Clik and Rain Bird WR2 are the most common wireless options. Transmitter batteries last a long time: Rain Bird states 4 years or more for the WR2, Hunter 10 years for the Wireless Rain-Clik. Hunter Solar Sync is a different product: a weather sensor that also measures sun and temperature, designed for compatible Hunter controllers. For most garden installations a wired sensor is the better value, and wireless is worth the premium only when you cannot run a cable.

FeatureWired sensorWireless sensor
Price€20–40Higher
Cable run neededYes (2-wire)No
Battery requiredNoYes (WR2: 4+ years; Wireless Rain-Clik: 10 years, per manufacturers)
Common modelsHunter Mini-Clik, Rain Bird RSDHunter Wireless Rain-Clik, Rain Bird WR2

Key takeaways

On an automatic irrigation system, a rain sensor returns the most for what it costs: a €20–40 device skips every cycle that would have run in the rain. Some places require it by law, Florida among them; elsewhere, check your local water authority. Mount in an unobstructed position at 1.5–2.5 m, away from roof overhangs and dense foliage. Connect to the SENS terminals and always remove the bypass jumper. Set the threshold at 5–6 mm for most garden soils. Choose a wired sensor for simplicity and reliability; wireless when the cable run is impractical.

Frequently asked questions

My controller has no SENS terminals. Can I still add a rain sensor?

Yes. Connect the rain sensor in series on the COM (common) wire: one sensor terminal joins the COM from the controller, the other joins the COM going to the solenoid valves. When wet, the sensor opens the COM circuit and no valve can open. This works on 24 V AC controllers; it does not work on battery controllers with latching solenoids, because the sensor would also block the pulse that closes the valve. For those, use a model with a sensor input.

The sensor keeps disabling irrigation even after a light shower. How do I fix it?

Two possible causes: the threshold is set too low (increase it to 8 mm), or the sensor is in shade and dries slowly. Check that the mounting position receives direct sun for at least a few hours after rain. If sun exposure is good, widen the vent aperture (the adjustable holes around the hygroscopic discs) to speed drying.

Can a rain sensor replace a smart controller?

The sensor covers rain-skip only. A smart controller adds ET-based adjustment (more water on hot windy days, less on cool cloudy ones), which a rain sensor cannot do. For maximum water savings, combine both: the sensor acts as a local failsafe when forecasts are wrong, and the smart controller optimises each cycle based on the previous day's weather.

Recommended products

These product links are affiliate links: if you buy on Amazon or AliExpress through them it costs you nothing extra, but it helps us keep SprinklerMap alive as a project and create new useful content.

In the catalogue From our brand catalogue

These products are catalogued in our brand database, with the same description and price range you find on the manufacturer page.

Hunter Industries Hunter Industries 2/15 products
Model Type Description Radius (m) Price (€) Buy
📡 Mini-Clik Sensor Affordable rain sensor that interrupts the irrigation cycle when it rains. Easy installation on any controller. — €35-55 Amazon
📡 Rain-Clik Sensor Rain sensor with adjustable threshold (3–25 mm). The wired version stays the cheapest; the wireless kit with receiver costs around three times as much. Compatible with all Hunter controllers. — €55-160 Amazon
Rain Bird Rain Bird 1/10 products
Model Type Description Radius (m) Price (€) Buy
📡 RSD-BEx Sensor Rain sensor with manual bypass. Affordable, reliable, adjustable threshold from 3 to 13 mm. — €40-70 Amazon
Orbit Orbit 1/4 products
Model Type Description Radius (m) Price (€) Buy
📡 57069 Sensor Wireless rain sensor. Connects to any controller with a sensor input. Simple and reliable. — €60-90 Amazon

Other suggested products

Products not in the brand catalogue: generic material, tools and accessories where the right size matters more than the brand.

Amazon On Amazon Fast shipping and easy returns
Product Description Price (€) Buy
Hunter WR-CLIK wireless rain sensor Wireless Hunter rain sensor with receiver that wires to SENS terminals. Hunter rates the range at up to 800 ft (about 245 m) line of sight. Best choice when running a cable from sensor to controller is impractical. ~€45-70 Amazon
Orbit wireless rain sensor Lower-cost wireless rain sensor for standard 24 V AC controllers, with a receiver wired to the SENS terminals. Features vary across the range: check the specifications of the exact model before buying. ~€25-40 Amazon
AliExpress On AliExpress Cheaper alternatives, slower shipping
Product Description Price (€) Buy
Rain sensor for irrigation controllers Hygroscopic-disc or wireless sensor that stops the cycle when it rains. Works with the usual 24V sensor input on controllers. ~€8-20 AliExpress
Zigbee/WiFi soil moisture sensor Wireless in-ground probe reporting soil moisture and temperature in-app. With Home Assistant or Zigbee2MQTT it becomes the trigger to skip pointless cycles. ~€8-20 AliExpress

Technical note: The compatibility of the smart devices mentioned in this article (WiFi/Zigbee protocol, app, power supply) can change with manufacturer firmware updates and isn't guaranteed with every existing valve or controller. Before buying, always check compatibility with your current system and your home network on the manufacturer's website. None of the models mentioned was tested directly: the comparison is on the specifications declared by the manufacturers.

Free tool: SprinklerMap is a free irrigation design tool — draw your yard, let it place the heads with head-to-head spacing, and get a full parts list in minutes. Works in feet, GPM and PSI, or in metric: see the planner for Australia & NZ. Open the app →

Related articles