Published May 4, 2026 · Updated November 17, 2026 · 11 min read · by Giacomo Falaschi

How to design irrigation for a rectangular garden

A complete case study built in SprinklerMap: a 10×8 m garden designed step by step: survey, 4 rotors, wetting simulation, 89.5% coverage and a real parts list from €313 to €539.

The case study: a real 80 m² design, number by number

The garden in the screenshots is a real project drawn in SprinklerMap, and every number you will read (coverage, metres of pipe, watering minutes, prices) is what the app calculated on that design. The case is the most common residential layout there is: a 10 × 8 metre rectangle, 80 m² of lawn in full sun, with no pools, trees or beds breaking the geometry.

The project settings are those of a typical household supply: 2.5 bar dynamic pressure, 15 L/min available flow, loam soil. The end result, built step by step below: 4 pop-up rotors in the corners, 34.6 m of polyethylene pipe, 89.5% coverage and a complete parts list between €313 and €539. If your garden is bigger or shaped differently, the last section gives you the rules to adapt every step.

Step 1: Measure and draw to scale

Everything starts with two measurements taken with a tape measure or laser meter: 10.0 m on the long side, 8.0 m on the short one. It sounds trivial, but precision here counts double, because every survey error propagates into sprinkler radius, pipe length and the final quote. Measure both opposite sides, not just one: in real "rectangular" gardens they often differ by 20-30 cm, and in that case you should draw the actual trapezoid, not the ideal rectangle.

In the drawing canvas the scale is fixed and stated (at 100% zoom one metre is 50 pixels), and the app shows each edge length live as you place the vertices: the rectangle in the screenshot closes at exactly 10.0 × 8.0 m, that is 80.0 m². If you would rather start from your garden's true boundaries instead of a free drawing, you can trace them directly on the satellite map with GPS: the full procedure is in How to map irrigation zones in your garden.

The 10 × 8 m perimeter drawn in SprinklerMap: edge measurements update at every vertex (at 100% zoom, 1 m = 50 px)
The 10 × 8 m perimeter drawn in SprinklerMap: edge measurements update at every vertex (at 100% zoom, 1 m = 50 px)

Step 2: Auto placement: 4 corner rotors at 90°

With the perimeter closed, the Auto button generates the layout. The perimeter-priority algorithm applies a rule professional installers take for granted and beginners almost always ignore: sprinklers go in the corners and along the edges with reduced arcs (90° in a corner, 180° at mid-side), never in the middle of the lawn spraying outwards onto walls and pavements. On our rectangle the result is 4 rotors in the corners, each with a 90° arc and a 7.8 m working radius.

With a 7.8 m radius, each rotor practically reaches its neighbour across the 8 m side: that is the head-to-head principle behind uniform coverage, explained in detail in Sprinkler Head Spacing: The One Decision That Decides Whether Your Lawn Goes Brown. Along the 10 m side the jet stops 2.2 m short of the next head, so the bands at mid-side get less water. The overlapping arcs in the screenshot are intentional: a jet always delivers less water towards the end of its throw, and overlapping two decaying jets is the only way to get uniform precipitation in the middle band.

Automatic placement with perimeter priority: 4 corner rotors with a 90° arc and 7.8 m radius, head-to-head coverage arcs
Automatic placement with perimeter priority: 4 corner rotors with a 90° arc and 7.8 m radius, head-to-head coverage arcs

Step 3: The simulation: find the weak spots before you dig

Before buying anything, the simulation colours the lawn with the water it would receive: dark green where jets add up, light green where a single jet lands. On our project the map shows the classic four-sector pattern: the centre and diagonals get more, the mid-side bands stay lighter but covered.

You cannot do this step on paper. If the simulation shows a dry zone (it happens on more elongated rectangles, above 12-13 m), fixing it now costs one click (an extra rotor at mid-side), while fixing it after installation costs a reopened trench. After the install, the ground-truth check on the real lawn is the catch-cup test, with some cups right at the middle of the long sides: the method is in The catch-cup test: measure sprinkler uniformity and your real inches per hour.

The wetting simulation on the project: darker green where jets overlap, lighter where only one jet lands
The wetting simulation on the project: darker green where jets overlap, lighter where only one jet lands

Step 4: The project numbers: 89.5% coverage, 49 minutes a day

The Areas panel sums the project up in four measured lines: 80.0 m² of garden, 71.6 m² covered, 89.5% efficiency, 34.6 m of pipe. The uncovered 10% is the thin band along the edges at mid-side, where the corner jets arrive at the limit of their throw. If you want to get close to 100% you can move to 6 sprinklers (4 corners at 90° plus 2 at the middle of the long sides at 180°) for an extra €60-90. Each 180° head draws about twice as much as a 90° corner head, so the flow goes from 10.2 to about 20 L/min and the layout needs two zones. That is worth it above 12 m of side length; on 80 m², nearly 90% with 4 rotors on one zone is the simpler choice.

The irrigation section computes the water need with the evapotranspiration method: for a lawn in full sun the peak ET is 5.0 mm per day, which on the 71.6 m² covered becomes 497 litres and, at the 10.2 L/min the 4 rotors draw, 49 minutes of watering per day at the height of summer. This is calculated, not taken from a table: change vegetation, exposure or soil in the panel and times and litres are recalculated for your case. Why ET is the right basis for this calculation is explained in Why Evapotranspiration Is the Foundation of Modern Irrigation: the FAO-56 Paper Explained.

The precipitation analysis closes the loop: the 4 rotors deliver 8.6 mm/h, below the infiltration rate of loam soil and even of clay (about 12 mm/h), and indeed the app's indicator stays in the green "slow, optimal" band. Even on clay the 49 minutes would not need splitting into cycles; with sprays instead of rotors it would be a different story. The correct run times for each soil type are in How long to run sprinklers: minutes per cycle by soil and head type, with the math behind them.

The project's Areas panel: 71.6 m² covered out of 80.0 (89.5%), 34.6 m of pipe, 5.0 mm ET (the screenshot shows 33 minutes a day, from an earlier version of the calculation; today it is 49)
The project's Areas panel: 71.6 m² covered out of 80.0 (89.5%), 34.6 m of pipe, 5.0 mm ET (the screenshot shows 33 minutes a day, from an earlier version of the calculation; today it is 49)

Step 5: The generated parts list: €313 to €539

The parts list is generated from the drawing, not from generic formulas: 4 rotors because that is what the algorithm placed, 35 m of pipe because the route measured on the project is 34.6 m rounded to the cut, 12 fittings counted on the actual network nodes. For every line the app offers alternative models with their price, from Hunter PGP Ultra rotors at €12-26 to the Gardena T380 at €30-45, and it is almost entirely this choice that moves the total from the bottom to the top of the range.

The two optional-but-recommended lines, rain sensor and soil moisture sensor (€90-140 together), skip the waterings that would otherwise run in the rain or on soil that is still wet: how they work is in Rain sensor for irrigation: legal requirement and how it works. The time estimate is between 4 h 15 min and 7 h 35 min for 80 m², digging included: one relaxed weekend for two people. The comparison between this DIY build and turnkey quotes for the same size is in How much does a sprinkler system cost? Parts, installer quotes, backflow, and the water bill nobody budgets.

ComponentQuantityPriceEst. install time
Pop-up rotors (Gardena T380; alternatives Hunter PGP Ultra, Rain Bird 5000)4€120–1801 h – 1 h 40 min
25 mm PE pipe35 m€28–5335 min – 1 h 10 min
PE fittings (tees, 90° elbows)12 pcs€12–361 h – 2 h
Solenoid valve1€15–3030 – 45 min
Controller / timer1€30–5530 min – 1 h
Rain sensor1€60–9020 – 30 min
Soil moisture sensor1€30–5020 – 30 min
Lawn seed (trench repair)2.4 kg€18–45—
Total—€313–5394 h 15 min – 7 h 35 min
The parts list generated from the project: estimated total €313-539 and 4 h 15 min - 7 h 35 min of installation
The parts list generated from the project: estimated total €313-539 and 4 h 15 min - 7 h 35 min of installation

Adapting the method to your own rectangle

Change the size and the layout changes, not the method. The rules this case study makes concrete: up to about 9-10 m of side length, 4 corner sprinklers with a radius equal to the short side are enough; when the long side reaches about twice the corner radius, add 180° sprinklers along it so that heads are no farther apart than the effective radius. The usable radius depends on your real pressure, not the one on the box: measure it with the gauge method described in How to measure water pressure for irrigation before choosing models.

The second constraint is flow: our 4 rotors together use about 10.2 L/min of the 15 L/min available. A zone should stay under about 80% of the measured flow, so a single zone like this one needs about 13 L/min at the tap (10.2 ÷ 0.8): with 15 L/min it fits, with a little margin. The check for your case is always the same: measure your real flow with a bucket and a stopwatch, use 80% of it as the budget, divide by the unit flow of your chosen sprinklers; if the total does not fit, the system splits into several zones with one solenoid valve each. And if there are beds or hedges besides the lawn, they belong on a separate drip zone anyway: the reason is in Hydrozones: split your garden to irrigate better.

On pipe routing, two tips: on a rectangle the most robust line is the closed perimeter loop, which balances pressure from both sides; and every sprinkler should hang off its tee on a 30-40 cm flexible swing pipe, never rigid, because it absorbs ground movement and lets you adjust head height after backfilling. Buy 10% extra fittings as spares. Then open the editor and draw your own rectangle.

Frequently asked questions

Why does the auto-placement algorithm put sprinklers in the corners instead of the middle of the lawn?

Because sprinklers in the middle spray outward onto walls and pavement. Professional installers take the perimeter-priority rule (corners at 90°, mid-side at 180°) for granted: on the case study's 10×8 m rectangle it produced 4 corner rotors with a 7.8 m radius and 89.5% coverage.

Why doesn't the 80 m² project reach 100% coverage?

The uncovered 10% is a thin band along the edges at mid-side, where the corner jets reach the limit of their throw. Moving to 6 sprinklers (adding 2 at mid-side, roughly €60-90 extra) closes that gap, but each 180° head draws about twice as much as a 90° corner head, so total flow roughly doubles and the system needs two zones. That is worth it above 12 m of side length; under that, about 90% coverage with 4 rotors on a single zone is a reasonable compromise.

What decides whether the project needs one zone or several?

Available flow, not garden size. The case study's 4 rotors together use about 10.2 L/min of the 15 L/min available, inside the 12 L/min a single zone can take under the 80% rule. If the layout needed more heads than the tap can support, the fix is splitting into additional zones with their own solenoid valve, not adding pressure.

How is the 49-minutes-a-day watering time calculated?

From evapotranspiration, not a preset table: a full-sun lawn's peak ET of 5.0 mm/day on the 71.6 m² the rotors cover works out to 497 litres, which at the 10.2 L/min the 4 rotors draw takes 49 minutes. Change the vegetation, exposure or soil and the app recalculates both figures for that specific case.

Recommended products

These product links are affiliate links: if you buy on Amazon or AliExpress through them it costs you nothing extra, but it helps us keep SprinklerMap alive as a project and create new useful content.

In the catalogue From our brand catalogue

These products are catalogued in our brand database, with the same description and price range you find on the manufacturer page.

Hunter Industries Hunter Industries 2/15 products
Model Type Description Radius (m) Price (€) Buy
🔄 I-20 Rotor Professional rotor with anti-theft retractable bolt. High flow rate for large gardens. Arc 40°–360°. 4.9–14 m €22-40 Amazon
🔧 PGV-101 Valve 1" residential solenoid valve. Female thread, manual override, ideal for single zones. — €22-42 Amazon
Rain Bird Rain Bird 1/10 products
Model Type Description Radius (m) Price (€) Buy
🖥️ ESP-RZXe (4-8 zone) Controller Easy-to-use indoor controller, 4-8 zones. 230 V power, optional LNK Wi-Fi module. — €85-160 Amazon

Other suggested products

Products not in the brand catalogue: generic material, tools and accessories where the right size matters more than the brand.

Amazon On Amazon Fast shipping and easy returns
Product Description Price (€) Buy
PE pipe 32 mm for buried irrigation High-density polyethylene pipe DN 32 mm PN6, 25 m coil. For high-flow main lines in gardens above 200 m². Flexible, frost-resistant, suitable for burial. ~€30-55 Amazon
Rain Bird 6-zone controller Rain Bird ESP-TM2 6-zone controller with 24 V AC valve outputs. Backlit LCD, 3 independent programs with 4 start times each, rain sensor input. Sized for residential systems with 4-6 zones. ~€50-90 Amazon
Hunter PGV 1" solenoid valve Hunter PGV 1" solenoid valve with manual bleed (flow control on the -B versions). Hunter lists 0.2-40 GPM (about 0.75-150 L/min) and 20-150 PSI (1.4-10 bar). A common choice for residential zones. ~€20-35 Amazon
AliExpress On AliExpress Cheaper alternatives, slower shipping
Product Description Price (€) Buy
Adjustable-arc pop-up rotors Gear-drive rotors with adjustable arc for medium lawns. Compare stated throw and flow against your zone before ordering: they vary a lot. ~€15-40 AliExpress
Irrigation solenoid valve 3/4"-1", 24V AC Solenoid valve compatible with standard 24V controllers. Good as a spare: check the thread and whether flow control is included. ~€8-20 AliExpress

Technical note: The numbers in this case study (coverage, pipe metres, times, litres and prices) were calculated by SprinklerMap on the project shown in the screenshots, with the stated settings (2.5 bar, 15 L/min, loam soil, 5.0 mm/day ET) and indicative August 2026 price lists. On 16 November 2026 flow, precipitation rate and minutes were recalculated after a correction to the app's nozzle flow estimate: the screenshots still show the earlier values (flow about 1.5 times higher for rotors, shorter run times). With different pressure, flow or soil the results can change substantially: redo the calculation for free on your own garden's drawing in the app before buying materials.

Free tool: SprinklerMap is a free irrigation design tool — draw your yard, let it place the heads with head-to-head spacing, and get a full parts list in minutes. Works in feet, GPM and PSI, or in metric: see the planner for Australia & NZ. Open the app →

Related articles